Electronics crapper is a very active and time-consuming hobby, who are interested in the districts. People who inspect electronics hobby run for hours and sometimes days to change construct electronics circuit that provides desired results. Caring is a prerequisite for a lot of circuit diagrams and the group's preference for different devices, ranging from burglar alarm and rockets that are acquirable on the market. Electronic components such as transistors, integrated chips (ICS), resistors and capacitors are also acquirable on the market at a reasonable price. It is just the electronics Maniacs, is a joyful hobby for their own use of energy and power in a constructive way.
E-work series are acquirable on the market, which significantly impair the long-electronics hobbyists making circuits. Lab kits provide electronic charts to build a good electronic equipment such as radio, camera, or a clock. Electronic components such as transistors, ICs, capacitors and resistors to allow the equipment and printed circuit, the Commission will also provide the link elements Kit. The individual is to be made how to solder these parts of its soldering iron and lead. Series of e-work are generally intended for teaching purposes. Equipment crapper be the work of electronic kits are generally nice to be a surprise and largely in value.
Showing posts with label electronic kits. Show all posts
Showing posts with label electronic kits. Show all posts
Wednesday, March 17, 2010
Sunday, February 21, 2010
Water Level Sensing and Control Circuit
Parts List
R1 = 10 ohm, 10 watt, wirewound
R2 = 100 ohm, potentiometer, wirewound
R3 = 1 Mega-ohm potentiometer
T1 = Transformer, 12.6volt, 1.2amp (min)
SCR1 = Silicon Controlled Rectifier, C106Y1, NTE5452, or equivalent
TR1 = TRIAC, SC141D, NTE5608, etc., rated 6-10 amp, 200-400 volt. TO-220.
Fuse = Slow-blow, 2 amp.
Saturday, February 20, 2010
Motor Cycle Alarm
Schematic:

Notes:
Any number of normally open switches may be used. Fit the mercury switches so that they close when the steering is moved or when the bike is lifted off its side-stand or pushed forward off its centre-stand. Use micro-switches to protect removable panels and the lids of panniers etc. While at least one switch remains closed, the siren will sound. About two minutes after the switches have been opened again, the alarm will reset. How long it takes to switch off depends on the characteristics of the actual components used. But, up to a point, you can adjust the time to suit your requirements by changing the value of C1.
Notes:
Any number of normally open switches may be used. Fit the mercury switches so that they close when the steering is moved or when the bike is lifted off its side-stand or pushed forward off its centre-stand. Use micro-switches to protect removable panels and the lids of panniers etc. While at least one switch remains closed, the siren will sound. About two minutes after the switches have been opened again, the alarm will reset. How long it takes to switch off depends on the characteristics of the actual components used. But, up to a point, you can adjust the time to suit your requirements by changing the value of C1.
Monday, February 15, 2010
Infra-red Level Detector
R1 : 10K 1/4W Resistor
R2,R5,R6,R9 : 1K 1/4W Resistors
R3 : 33R 1/4W Resistor
R4,R8 : 1M 1/4W Resistors
R7 : 10K Trimmer Cermet
R10 : 22K 1/4W Resistor
C1,C4 : 1΅F 63V Electrolytic or Polyester Capacitors
C2 : 47pF 63V Ceramic Capacitor
C3,C5,C6 : 100΅F 25V Electrolytic Capacitors
D1 : Infra-red LED
D2 : Infra-red Photo Diode (see Notes)
D3,D4 : 1N4148 75V 150mA Diode
D5 : LED (Any color and size)
D6,D7 : 1N4002 100V 1A Diodes
Q1 : BC327 45V 800mA PNP Transistor
IC1 : 555 Timer IC
IC2 : LM358 Low Power Dual Op-amp
IC3 : 7812 12V 1A Positive voltage regulator IC
RL1 : Relay with SPDT 2A @ 220V switch
Coil Voltage 12V. Coil resistance 200-300 Ohm
J1 : Two ways output socket
Device purpose:
This circuit is useful in liquids level or proximity detection. It operates detecting the distance from the target by reflection of an infra-red beam. It can safely detect the level of a liquid in a tank without any contact with the liquid itself. The device's range can be set from a couple of cm. to about 50 cm. by means of a trimmer.
Range can vary, depending on infra-red transmitting and receiving LEDs used and is mostly affected by the color of the reflecting surface. Black surfaces lower greatly the device's sensitivity.
Circuit operation:
IC1 forms an oscillator driving the infra-red LED by means of 0.8mSec. pulses at 120Hz frequency and about 300mA peak current. D1 & D2 are placed facing the target on the same line, a couple of centimeters apart, on a short breadboard strip. D2 picks-up the infra-red beam generated by D1 and reflected by the surface placed in front of it. The signal is amplified by IC2A and peak detected by D4 & C4. Diode D3, with R5 & R6, compensate for the forward diode drop of D4. A DC voltage proportional to the distance of the reflecting object and D1 & D2 feeds the inverting input of the voltage comparator IC2B. This comparator switches on and off the LED and the optional relay via Q1, comparing its input voltage to the reference voltage at its non-inverting input set by the Trimmer R7.
Notes:
* Power supply must be regulated (hence the use of IC3) for precise reference voltages. The circuit can be fed by a commercial wall plug-in power supply, having a DC output voltage in the range 12-24V.
* Current drawing: LED off 40mA; LED and Relay on 70mA @ 12V DC supply.
* R10, C6, Q1, D6, D7, RL1 and J1 can be omitted if relay operation is not required.
* The infra-red Photo Diode D2, should be of the type incorporating an optical sunlight filter: these components appear in black plastic cases. Some of them resemble TO92 transistors: in this case, please note that the sensitive surface is the curved, not the flat one.
* Avoid sun or artificial light hitting directly D1 & D2.
* Usually D1-D2 optimum distance lies in the range 1.5-3 cm.
* If you are needing a similar circuit driving 3 LEDs in sequence, also suitable as a parking aid, click here
Source http://www.electronics-lab.com
Subscribe to:
Posts (Atom)